Simplicity

Engine information on popular Simplicity Models

Simplicity 12.5LTH

Original Model: Briggs Various
One of the engines used in this mower was the 260777-0131. There is no complete engine or short block to replace this engine. Another engine that was used on this was the Briggs Vanguard 12.5hp twin 290777 in which you can buy the 351776 and add your starter to it.

Simplicity 12RTH

Original Model: Briggs 283707-0110
The original engine is no longer available. The newer overhead valve engines have the same mounting but the engines are about 2ö wider and 2ö longer than the flathead engines (non overhead valve) the muffler will be on the opposite side of the engine and the fuel pumps pull there vacuum from the dipstick tube instead of the side plate on the flathead engine. Due to this difference if you currently have a fuel pump on your engine you would have to purchase an engine with a fuel pump.

Simplicity 16LTH

Original Model: Briggs Vangaurd 303777 16HP
If you buy a recoil start engine you will have to use the starter, flywheel, and alternator off of the original engine.

Simplicity 17GTH-L

Original Model: Kohler KT17
One of the original specs was 24305

Simplicity 1844

Original Model: Kohler Command 18hp CV493
This engine has a standard 1" keyed shaft on it and needs a fuel pump and a 15 amp alternator on it.
If you purchase a recoil start engine you would have to use your flywheel and starter of the old engine.

Simplicity 18GTH-L

Original Model: Misc
These were made with different engines in them. When repowering a tractor with a single cylinder you will need to use the single cylinder until a replacement is found for it. When replacing a Magnum series 18 or 20hp you can use one of our conversion kits for these tractors. If you have a Command in your tractor now, we can probably also get that same engine or a shortblock for it.

Simplicity 2010

Original Model: 243431
This tractor uses a belt type starter generator on the engine. If you use the front shaft it will be a 1" keyed shaft, if you don't use the front shaft then you could buy an engine with any shaft size.

Simplicity 2012

Original Model: 300431
This tractor uses a belt type starter generator on the engine. If you use the front shaft it will be a 1" keyed shaft, if you don't use the front shaft then you could buy an engine with any shaft size.

Simplicity 20GTH-L

Original Model: Misc
These were made with different engines in them. When repowering a tractor with a single cylinder you will need to use the single cylinder until a replacement is found for it. When replacing a Magnum series 18 or 20hp you can use one of our conversion kits for these tractors. If you have a Command in your tractor now, we can probably also get that same engine or a shortblock for it.

Simplicity 2210

Original Model: 243431
This tractor uses a belt type starter generator on the engine. If you use the front shaft it will be a 1" keyed shaft, if you don't use the front shaft then you could buy an engine with any shaft size.

Simplicity 3012

Original Model: Briggs Cast Iron 300421
These tractors were from the late 60's to the early 70's. Briggs no longer makes the cast iron series of engines, however we still have a few of the 10hp models Other engines may also work in here, however we have not had one of these tractors in here to engineer a kit for them.

Simplicity 3108

Original Model: Briggs 190707
This series of engine is no longer made. I am not sure if a different engine will work in it or not without seeing a couple pictures of this unit.

Simplicity 3110

Original Model: Briggs 220707
The throttle linkage is a little different between the older engines and the new engines, but this should still work fine for you. If you have an electric clutch you will need to use your alternator and regulator from your original engine, if you have a fuel pump you will also have to use that as well.

Simplicity 3112

Original Model: Briggs Cast Iron 300421
These tractors were from the late 60's to the early 70's. Briggs no longer makes the cast iron series of engines.

Simplicity 3210

Original Model: Briggs Cast Iron 243431
These tractors were from the late 60's to the early 70's. Briggs no longer makes the cast iron series of engines.

Simplicity 3212

Original Model: Briggs Cast Iron 300421
These tractors were from the late 60's to the early 70's. Briggs no longer makes the cast iron series of engines. Other engines may also work in here.

Simplicity 3310

Original Model: Briggs Cast Iron 243431
These tractors were from the late 60's to the early 70's. Briggs no longer makes the cast iron series of engines.

Simplicity 3410

Original Model: Briggs 243431 10hp
This tractor uses a belt type starter generator on the engine. This engine is no longer available.

Simplicity 3414

Original Model: 302431-0144
This tractor Drives of the flywheel side of the engine only. We have not had one of these tractors in here to see if anything else would fit but we have been told that the 3416 and the 3114 is the same frame.

Simplicity 3416

Original Model: 326431
This tractor uses a belt type starter generator on the engine. If you use the front shaft it will be a 1" keyed shaft, if you don't use the front shaft then you could buy an engine with any shaft size.

Simplicity 4040 

Original Model: CCK series Onan
A replacement shortblock for the original engine would be over $3,000. Our conversion kits include a drive adapter on the flywheel to bolt your pulley onto. Check your muffler style before ordering any kit. We wire these up to match the factory original four prong connector. The plate to mount the electric clutch to will work whether you have a brake on it or not. These kits include a new throttle and choke cable. The kits also include a mounting plate that you bolt down to your existing holes to raise the engine up to the required height. A new oil drain and tube comes with this to make it easy to change your oil. You do have to cut part of the baffle under your hood for this to clear the air filter assembly, no other cutting is required.

Simplicity 4041

Original Model: CCK series Onan
A replacement shortblock for the original engine would be over $3,000. Our conversion kits include a drive adapter on the flywheel to bolt your pulley onto. Check your muffler style before ordering any kit. We wire these up to match the factory original four prong connector. The plate to mount the electric clutch to will work whether you have a brake on it or not. These kits include a new throttle and choke cable. The kits also include a mounting plate that you bolt down to your existing holes to raise the engine up to the required height. A new oil drain and tube comes with this to make it easy to change your oil. You do have to cut part of the baffle under your hood for this to clear the air filter assembly, no other cutting is required.

Simplicity 4108

Original Model: Briggs 8hp 190707
This engine has a standard 1" keyed shaft on it. You can use a recoil start engine by using your starter, alternator, and flywheel from your original engine.

Simplicity 4111

Original Model: Briggs 11hp
This engine has a standard 1" keyed shaft on it. If you have an electric clutch you will have to use the alternator and regulator off of your old engine. If you have a fuel tank or fuel pump mounted to your engine you will also have to use it off of your old engine.

Simplicity 4208

Original Model: Briggs 8hp 190707
This engine has a standard 1" keyed shaft on it. You can use a recoil start engine by using your starter, alternator, and flywheel from your original engine.

Simplicity 4210

Original Model: Briggs 10HP 255707
This engine has a standard 1" keyed shaft on it.

Simplicity 4211

Original Model: Briggs 11hp 252707-0130
This engine has a standard 1" keyed shaft on it. If you use the OHV engine, you will also have to change the muffler which we cannot help with.

Simplicity 4212

Original Model: Briggs 281707
The throttle linkage is a little different between the older engines and the new engines, but this should still work fine for you. If you have an electric clutch you will need to use your alternator and regulator from your original engine, if you have a fuel pump you will also have to use that as well.

Simplicity 440ST

Original Model: Kohler Command CV16S-43510
This engine has a standard 1" keyed shaft on it and needs a fuel pump and a 15 amp alternator on it The 43510 engine uses a 1252218 shortblock.

Simplicity 5010

Original Model: Briggs 10hp 251707
This engine has a standard 1" keyed shaft on it.

Simplicity 5212.5

Original Model: 404707 12.5hp Briggs Opposed Twin
You would have to use your muffler and possibly your intake manifold off of your original engine If you have an electric clutch you will have to use your alternator and regulator as well.

Simplicity 5216

Original Model: 402707
You would have to use your muffler and possibly your intake manifold off of your original engine.

Simplicity 5526

Original Model: Briggs 18HP 350777-0113
You would have to use your muffler off of your original engine.

Simplicity 6010

Original Model: Briggs 10hp 251707-0169
This engine has a standard 1 keyed shaft on it.

Simplicity 6011

Original Model: Briggs 11hp 252707
This engine has a standard 1" keyed shaft on it.

Simplicity 611

Original Model: Briggs 11hp 252707-0630
This engine has a standard 1" keyed shaft on it.

Simplicity 6118

Original Model: Briggs 461707
If you have an electric clutch you will need to use your alternator and regulator from your original engine.

Simplicity 620

Original Model: CCK series Onan.

Simplicity 6211

Original Model: Briggs 11hp 252707
This engine has a standard 1" keyed shaft on it.

Simplicity 6216

Original Model: Briggs 402707
If you have an electric clutch you will need to use your alternator and regulator from your original engine.

Simplicity 627

Original Model: Briggs 7hp 170707
This engine has a standard 1 keyed shaft on it. You could also use a bendix type starter engine on it, but wiring changes would be necessary. This series of engine is no longer available. No other engine will fit in this frame because of the way the hood support bolts onto the head of the engine.

Simplicity 648

Original Model: Briggs 7hp 170707
This engine has a standard 1" keyed shaft on it. You could also use a bendix type starter engine on it, but wiring changes would be necessary.

Simplicity 6516

Original Model: Briggs 402707
If you have an electric clutch you will need to use your alternator and regulator from your original engine.

Simplicity 6516H

Original Model: Briggs 402707
If you have an electric clutch you will need to use your alternator and regulator from your original engine.

Simplicity 6517

Original Model: Kohler MV16S-56510
1"x3-5/32" Keyed Shaft NOTE: if you use the MV18T-58511 engine you would have to use your flywheel, starter and alternator to make the engine electric start.

Simplicity 7010

Original Model: Various
Some used the Briggs cast iron single cylinder and some used the Kohler single cylinder cast iron Briggs no longer makes this single cylinder cast iron engine, however we do have a few on hand right now You cannot interchange these two engines without changing the wiring and switch.

Simplicity 7012

Original Model: Kohler K301 12hp
The Kohler replacement engines all come with a 1 1/8" shaft, although the shaft is typically not used, you will need to check this before buying anything.

Simplicity 7013

Original Model: Briggs Cast Iron 13hp 302431-0155
Briggs no longer makes this single cylinder cast iron engine.

Simplicity 7014

Original Model: Briggs Cast Iron 14hp
Briggs no longer makes this single cylinder cast iron engine.

Simplicity 7016

Original Model: Briggs Cast Iron 326400
Briggs no longer makes this single cylinder cast iron engine.

Simplicity 7018

Original Model: Kohler K361 18hp
This tractor uses the Kohler OHV single cylinder that is no longer made and there is nothing that will directly fit it. One of the spec numbers was 23107a. Notes: Kohler discontinued this engine over 15 years ago, it was not designed to use unleaded gasoline in which makes the engine run hotter. Kohler recommends using the K341-71179 16hp, but the muffler does come out at a different angle and you would have to do modification to make it work.

Simplicity 707

Original Model: Briggs 7HP 171701
This engine has a standard 1" keyed shaft on it. You can use a recoil start engine by using your starter, alternator, and flywheel from your original engine. This series of engine is no longer available. No other engine will fit in this frame because of the way the hood support bolts onto the head of the engine.

Simplicity 7110

Original Model: K241 Kohler 10hp
If you use the front shaft on your engine you will need to find out what size it is before buying anything. They are generally 1" diameter and there is nothing that will directly replace them.

Simplicity 728

Original Model: Briggs 8HP 191701
This engine has a standard 1" keyed shaft on it. You can use a recoil start engine by using your starter, alternator, and flywheel from your original engine. This series of engine is no longer available. No other engine will fit in this frame because of the way the hood support bolts onto the head of the engine.

Simplicity 7112

Original Model: K301 Kohler 12hp
If you use the front shaft on your engine you will need to find out what size it is before buying anything. They are generally 1" diameter and there is nothing that will directly replace them.

Simplicity 7114

Original Model: Briggs 14hp Cast Iron
Briggs no longer makes this single cylinder cast iron engine If you use the front shaft on your engine you will need to find out what size it is before buying anything. They are generally 1" diameter and there is nothing that will directly replace them.

Simplicity 7116

Original Model: 326437
Briggs no longer makes this single cylinder cast iron engine If you use the front shaft on your engine you will need to find out what size it is before buying anything. They are generally 1" diameter and there is nothing that will directly replace them.

Simplicity 7117

Original Model: Kohler KT17
One of the original specs was 24305 The original Kohler engine is too overpriced now. Shortblock 8252202 will replace the KT17 Kohler engine If you do not use the front shaft on your engine you could use the KT17EP-24365 and change some of your parts over to it and save a lot of money.

Simplicity 7119

Original Model: KT19
One of the common spec numbers of the original Kohler engine was 49225, the 52 522 84 shortblock is the replacement for it.

Simplicity 717 Boadmoor

Original Model: Briggs model 191700, type 0638

Simplicity 725

Original Model: Briggs model 19
This has an all cast iron engine.

Simplicity 727 Boadmoor

Original Model: Briggs model 191700, type 0638

Simplicity 738

Original Model: Briggs 8HP 191700-0638
This engine has a standard 1" keyed shaft on it. You can use a recoil start engine by using your starter, alternator, and flywheel from your original engine. This series of engine is no longer available. No other engine will fit in this frame because of the way the hood support bolts onto the head of the engine.

Simplicity 9020

Original Model: CCK series Onan

Simplicity 918H

Original Model: Kohler Command CH18S-62513

Simplicity B210

Original Model: Briggs 233431 10hp Cast Iron.
If you do not use the front shaft of our engine you can use a tapered or threaded shaft on this tractor. If you use the front shaft it will be a 1" diameter. Other engines possibly would work, however we haven't done any conversions with any other makes or models yet.

Simplicity Broadmoor

Original Model: Various Models
If you have a Briggs Vanguard 303777 twin cylinder engine, you will have to go back with another Vanguard Twin Engine.
If you have a Briggs Intek twin vertical, 405777-0134, you will Have to use an Intek Twin.
If you have a Kohler Command single cylinder engine, we will need to see pictures of your engine installed in the tractor to see if we have any options for you.
On the earliest models of these tractors they bolted the hood bracket to the cylinder head, if yours is this way you will have to stick with the same series of engine. Other than that you can go up in HP as long as you stay with a non-OHV engine If you have an electric clutch you will have to use the alternator and regulator off of your old engine unless you buy an engine with a 9 amp alternator or larger. If you have a fuel tank or fuel pump mounted to your engine you will also have to use it off of your old engine unless you buy an engine with it already installed. If you have a mower that was made in the 90's or later and has an OHV engine in it you will need to go back with another OHV engine. If your frame looks like the one in the picture below where your oil filter is wide open you could install a new engine with a filter as well, otherwise you would have to go with an engine without a filter because they stick stragiht out the side now instead on going forward. If your frame sticks up on the side close to the carburetor area the only thing you could use and keep a filter on it is our SB497149 shortblock or an engine without the filter on it.

Simplicity Cavalier

Original Model: Briggs 256707-0110-01 10 HP

Simplicity CFC20

Original Model: M20S-49595
This is an older 60" Commercial Front Cut Mower. The engine shaft is 1" x 3"

Simplicity Champion

Original Model: Kohler Command 18hp CV493
This engine has a standard 1" keyed shaft on it and needs a fuel pump and a 15 amp alternator on it.
If you purchase a recoil start engine you would have to use your flywheel and starter of the old engine.

Simplicity Conquest

Original Model: Various engines
One of the engines used was a Briggs 356777-0113 18hp Vanguard, 1" x 3-5/32" shaft, 16 Amp Alternator, Electric Start, and Fuel Pump.

Simplicity Coronet

Original Model: Various engines
One of the engines used was a Kohler Command CV12.5-1277 which did not have a fuel pump on it but has a 15 amp alternator on it. if you get the Command listed here, you would need to change the alternator from your old engine to the new one. I have been told that a Tecumseh OHV125-203031B has also been used on this mower.

Simplicity FCH16

Original Model: Briggs 303777-0122
This engine has a 1" x 3 5/32" shaft.

Simplicity GTH16

Original Model: Briggs 16hp Vanguard 303777-0122.

Simplicity Lancer

Original Model: Briggs Intek OHV Vertical
This unit has a fuel pump and also has an electric clutch to engage the mower blades.

Simplicity Landlord

Original Model: Various models.
Some the newer tractors used a 350777 vertical shaft Briggs Vanguard engine in them, if you buy the 35777A-0113 engine you will need to use your starter or cut the frame for our solenoid to fit down in it. Most of the older tractors used a horizontal shaft engine with the shaft out the front and one engine used in the older models was a 23D in which the 233431 or 243431 and typically had a belt driven starter generator on it. If you use the front shaft it will be a 1" keyed shaft, if you don't use the front shaft then you could buy an engine with any shaft size.

Simplicity Legacy

Original Model: Various engines.
One of the engines used was a Kawasaki FD750D 27hp Water Cooled. Another engine used was a Kohler Command CH740-3147.

Simplicity PowerMax

Original Model: CCK series Onan.

Simplicity Prestige

Original Model: Kohler Command CV20-65582 or CV23S-75553.
The 65582 and the 75553 engines have a 1"x3-5/32" shaft on them. The engines listed here would have the same mounting and shaft size. There might be minor differences however parts are interchangeable.

Simplicity Regent

Original Model: Various Models.
If your tractor had an OHV engine on it you need to go back with an OHV engine. If your tractor had a non OHV engine on it, you need to go back with a non OHV engine. The mufflers are totally different between these two engines and it will cause you some problems to switch. Most of these tractors used a 28Q777 Briggs engine with an oil filter bracket that bolted onto the oil pan. If your is this way you will not be able to use another engine with an oil filter on it. The newer engines use a filter that screws directly onto the oil pan and will be in the way of the frame. At this time I would recommend that you install an engine that does not have an oil filter on it so you do not get into any problems with it fitting. If your tractor has an electric clutch on it you will need to buy and engine with a 9 amp or larger alternator to run it. If you tractor has a fuel pump on the engine, you will need to buy and engine with it already installed, or use the old one off of your engine and also the valve breather. If you purchase an AVS style Briggs engine the fuel pump draws its vacuum from the dip stick tube. If the AVS style engine has no fuel pump you would have to buy a new dipstick tube. You cannot change from one brand to another without major problems especially on the muffler. One of the Kohler models was a CV16S-43510.

Simplicity Sovereign 

Original Model: Multiple
There are many model of different engines that have been used in this model of tractor. You will have to go back with the same model as the original engine that came in your tractor.
If you have a newer tractor that came out with a Kohler Command you will have to go back with a Command engine.
If you have the Kohler Triad OHC engine you could use our conversion kit listed.
If you have an earlier tractor that had the Briggs single cylinder engine in it, there is currently no engine available for it.
If you have a Kohler Magnum, you can use the 8252227 Shortblock.

Simplicity Sunrunner

Original Model: Briggs 281707.
If you have an electric clutch you will have to use the alternator and regulator off of your old engine. If you have a fuel tank or fuel pump mounted to your engine you will also have to use it off of your old engine.

Simplicity Sunstar

Original Model: Misc
These were made with different engines in them. When repowering a tractor with a single cylinder you will need to use the single cylinder until a replacement is found for it.

Simplicity Yeoman

Original Model: Briggs 7hp 170707 and 8 hp 190707
This engine has a standard 1 keyed shaft on it. You could also use a bendix type starter engine on it, but wiring changes would be necessary. This series of engine is no longer available. No other engine will fit in this frame because of the way the hood support bolts onto the head of the engine.

Simplicity ZT1850

Original Model: Briggs Vanguard 350777
You have to change minor parts from your original engine if you are using either of these engines.

Simplicity ZT2148

Original Model: Kohler CV22S-75564
This engine has a 1 1/8" diameter shaft that is 4 3/8" in length. The exact engine is no longer available through Kohler.

Simplicity ZT2352T Derby Colt

Original Model: Kohler CV23S-75562.
This engine has a 1 1/8" x 4 3/8" shaft. The cv23s-75562 engine is no longer available. Our engine CV730 & CV740 would have the same mounting and the same shaft size. There may be minor differences however parts would be interchangeable if needed.